Automotive Test Scope ATS605004DW-XMS

The WiFi labscope packed with technology

Price:  2,341.00

Key specifications

  • WiFi / LAN / USB connected
  • 14 bit (0.006 %) resolution (16 bit enhanced resolution)
  • Up to 500 MSa/s sampling
  • 250 MHz bandwidth
  • Up to 100 MSa/s continuous streaming
  • Up to 256 Mpoints memory per channel
  • 0.25 % DC vertical accuracy, 0.1 % typical
  • 1 ppm time base accuracy

Full specifications Manual Request info

Order code: ATS605004DW-XMS
EAN: 7423622826804
Price: 2,341.00

WiFi connected

Using a computer based oscilloscope was never easier than with the Automotive Test Scope ATS605004DW-XMS: simply switch it on and start the software on the computer:

  • no power cables required as it is battery powered and can operate hours on a fully charged battery
  • no interface cables required as it uses WiFi to connect to the computer

This allows you to measure fully floating, fully isolated from your computer. The Automotive Test Scope ATS605004DW-XMS can be placed near any test subject that may be hard to reach, or on moving objects, where wired connections are not possible.

Because the Automotive Test Scope ATS605004DW-XMS is not connected to the computer, there is no risk of damaging the computer.

LAN connected

When measuring in remote locations where a wired network is available, the Automotive Test Scope ATS605004DW-XMS can also be used through its LAN port. Measurements can then be performed from any location via the network, without having the computer to be close to the test subject.

Using its 1 Gbit LAN connection, the Automotive Test Scope ATS605004DW-XMS can achieve higher streaming performance than via WiFi.

USB 3.0 connected

When wireless measuring or LAN connected measuring is not required or not possible, the Automotive Test Scope ATS605004DW-XMS can also be connected via its USB3 port. This gives the benefit of even higher streaming performance. Additionally, when connected via USB, the Automotive Test Scope ATS605004DW-XMS can be combined with oscilloscopes via its CMI interface.

View all ways to connect

This powerful automotive WiFi oscilloscope combines fast sampling up to 1 GSa/s with high resolutions of 12, 14 and 16 bit and a large memory of 64 Mpoints per channel with four differential channels. Additionally, the automotive WiFi oscilloscope supports continuous streaming measurements up to 200 MSa/s.

The Automotive Test Scope ATS605004DW-XMS is delivered with SureConnect connection test and resistance measurement on each channel.

Rugged industrial design

The Automotive Test Scope ATS605004DW-XMS features a rugged design. Its enclosure is fitted with rubber protectors at the front and the rear. These protect the Automotive Test Scope ATS605004DW-XMS against damage by mechanical shocks. The rubber helps absorbing shocks and protects the connectors at the front and the rear of the Automotive Test Scope ATS605004DW-XMS, these fall within the protected zone.

Additionally, the rubber prevents your Automotive Test Scope ATS605004DW-XMS from sliding. The rubber protectors have special notches that simplify stacking instruments. Holes are included that allow to connect a strap to hang the instrument near the test subject.

WiFiScope Front sideview

Safe measuring

The Automotive Test Scope ATS605004DW-XMS is a four channel automotive oscilloscope with differential inputs. With the differential inputs it is possible to measure four totally unrelated signals simultaneously. It is no longer possible to create a short circuit through the oscilloscope or through a second device connected to your computer and to the car, like e.g. a fault code scanner. So no risk of damaging the car, the oscilloscope or the computer.

Read differential input details

SureConnect

The SureConnect connection test feature of the Automotive Test Scope ATS605004DW-XMS tells you immediately whether your test probe or clip actually makes electrical contact or not. No more doubt whether your probe doesn't make contact or there really is no signal.

This is useful when surfaces are oxidized and your probe cannot get a good electrical contact. Simply activate the SureConnect and you know whether there is contact or not. Also when back probing connectors in confined places, SureConnect immediately shows whether the probes make contact or not.

SureConnect is default available on each channel of the Automotive Test Scope ATS605004DW-XMS.

Read SureConnect details

Resistance measurement

Many automotive sensors are based on variable resistors. Use your Automotive Test Scope ATS605004DW-XMS in the resistance setting to test them, no more need to take a separate ohm meter. Resistance values can be displayed as a number, but it is also possible to display the resistance variation in time, in a graph.

The unique Automotive Test Scope ATS605004DW-XMS Ohm scope is the first fast automotive Ohm scope in its class.

Read resistance measurement details

Large memory

When measuring at high sample rates, a large memory is necessary to be able to record a complete signal in the acquisition buffer. Where most oscilloscopes have 2.5 kpoints or 100 kpoints memory, the Automotive Test Scope ATS605004DW-XMS has up to 256 Mpoints memory per channel. An advantage of a large memory is that once-only fast phenomena can be captured accurately or complete serial communication signal blocks can be measured all at once.

Read large memory details

High accuracy

The Automotive Test Scope ATS605004DW-XMS measures with high resolutions of 14 and 16 bit. A signal measured with the Automotive Test Scope ATS605004DW-XMS therefore has 256 times more resolution than most standard automotive oscilloscopes, which usually have a low resolution of 8 or 9 bit. The input circuit of the Automotive Test Scope ATS605004DW-XMS has a high accuracy of 0.25 % of the full scale input range, where most standard automotive oscilloscopes have an accuracy of 2 - 3 % of the full scale range. The precision Automotive Test Scope ATS605004DW-XMS allows for measuring signals with much more accuracy.

Read high accuracy details

Automotive Test Scope ATS605004DW-XMS specifications

The tables below show detailed specifications of the Automotive Test Scope ATS605004DW-XMS. Jump to specifications regarding

Acquisition system

Number of input channels4 analog
CH1, CH2, CH3, CH4Isolated female BNC
TypeDifferential input
ResolutionUser selectable in software
Native8, 12, 14 bit
Enhanced16 bit
DC Accuracy0.25 % (0.1 % typical) of full scale ± 1 LSB at 20°C to 25°C
To achieve rated accuracy, allow the instrument to settle for 20 minutes. When subjected to extreme temperatures, allow additional time for internal temperatures to stabilize.
Ranges (full scale)±200 mV
±400 mV
±800 mV
±2 V
±4 V
±8 V
±20 V
±40 V
±80 V
CouplingAC/DC
Impedance2 MOhm / 12 pF ± 1 %
Noise (in 200 mV range)300 µVrms
Maximum voltage200 V (DC + AC peak < 10 kHz)
Maximum Common Mode voltage200 mV to 800 mV ranges : 2 V
2 V to 8 V ranges : 20 V
20 V to 80 V ranges : 200 V
Common Mode Rejection Ratio-47 dB
Bandwidth 
-3dB at 75 % of full scale input250 MHz
Limit, selectable per channelOff (250 MHz)
150 MHz
100 MHz
50 MHz
AC coupling cut off frequency (-3dB)±1.5 Hz
SureConnect 
Maximum voltage on connection200 V (DC + AC peak < 10 kHz)
Resistance measurement 
Ranges (Full scale)1 kΩ
2 kΩ
5 kΩ
10 kΩ
20 kΩ
50 kΩ
100 kΩ
200 kΩ
500 kΩ
1 MΩ
2 MΩ
Accuracy1 % of full scale
Response time (to 95%)< 10 µs
 
Maximum sampling ratemeasuring one channelmeasuring two channelsmeasuring three or four channels
8 bit500 MSa/s200 MSa/s100 MSa/s
12 bit200 MSa/s100 MSa/s50 MSa/s
14 bit50 MSa/s50 MSa/s50 MSa/s
16 bit3.125 MSa/s3.125 MSa/s3.125 MSa/s
 
Maximum streaming rate 1measuring one channelmeasuring two channelsmeasuring three or four channels
8 bit100 MSa/s 250 MSa/s 325 MSa/s 4
12 bit50 MSa/s 325 MSa/s 412.5 MSa/s 5
14 bit50 MSa/s 325 MSa/s 412.5 MSa/s 5
16 bit3.125 MSa/s3.125 MSa/s3.125 MSa/s
  1. Due to computer restrictions, on some computers the highest streaming rates may not be available.
    When LAN/WiFi connected, the maximum streaming rate is limited, and depends on the quality of the network.
  2. ≤ 40 MSs/s when connected to USB 2.0 or via LAN/WiFi
  3. ≤ 20 MSs/s when connected to USB 2.0 or via LAN/WiFi
  4. ≤ 10 MSs/s when connected to USB 2.0 or via LAN/WiFi
  5. ≤ 5 MSs/s when connected to USB 2.0 or via LAN/WiFi
  6. ≤ 3.125 MSs/s when connected to USB 2.0 or via LAN/WiFi
 
Sampling clock source 
InternalTCXO
Accuracy± 0.0001 %
Stability± 1 ppm over 0°C to 55°C
Time base aging±1 ppm/year
ExternalLVDS, on CMI connectors
Input frequency10 MHz ± 1 %
16.369 MHz ± 1 %
 
Memorymeasuring one channelmeasuring two channelsmeasuring three or four channels
via USB 
8 bit resolution256 MSa per channel128 MSa per channel64 MSa per channel
12, 14, 16 bit resolution128 MSa per channel64 MSa per channel32 MSa per channel
via LAN/WiFi 
8 bit resolution64 MSa per channel32 MSa per channel16 MSa per channel
12, 14, 16 bit resolution32 MSa per channel16 MSa per channel8 MSa per channel
 
Trigger 
SystemDigital, 2 levels
SourceCH1, CH2, CH3, CH4, OR, digital external
Trigger modesRising edge, Falling edge, Any edge
Inside window, Outside window, Enter window, Exit window (time conditions only on Ch1)
Pulse width (only on Ch1)
Interval (only on Ch1)
Level adjustment0 to 100 % of full scale
Hysteresis adjustment0 to 100 % of full scale
Resolution0.006 % (14, 16 bits) / 0.025% (12 bits)
Pre trigger0 to selected record length, 1 sample resolution
Post trigger0 to selected record length, 1 sample resolution
Trigger hold-off0 to 63 MSamples, 1 sample resolution
Trigger delay0 to 8 GSamples, 1 sample resolution
Digital external trigger 
InputExtension connector pins 1 and 2
Range0 to 2.5 V (TTL)
CouplingDC
Jitter≤ 1 sample

Multi-instrument synchronization

Using CMISynchronizing instruments via CMI is available when all instruments are connected via USB.
Maximum number of instrumentsLimited by number of available USB ports
Synchronization accuracy0 ppm
CMI interface2x, CMI 1, CMI 2
Required coupling cableTP-C50H Coupling cable CMI
Maximum coupling cable length50 cm
Using WCMISynchronizing instruments via WCMI is available when instruments are connected via USB, LAN and WiFi.
Maximum number of instrumentsNo limitation
Required coupling moduleWCMI - 8, WCMI - 9
Clock synchronization accuracy≤ 1 ppm, typical ≤ 0.2 ppm
Trigger jitter at sample rate 1≤ 1 MSa/s> 1 MSa/s
2 x "5"≤ ±2 samples≤ ±2 µs
"5" and "6" 
Trigger source "5"≤ ±2 samples≤ ±2 µs
Trigger source "6"≤ ±8 samples≤ ±8 µs
2 x "6"≤ ±8 samples≤ ±8 µs
  1. "5" = WiFiScope WS5 or Handyscope HS5.
    "6" = WiFiScope WS6 DIFF, WiFiScope WS6, Handyscope HS6 DIFF, Handyscope HS6, ATS610004DW-XMSG, ATS610004D-XMSG, ATS605004DW-XMS or ATS605004D-XMS

Probe calibration

OutputExtension connector pins 3 (signal) and 6 (ground)
SignalSquare wave
Level-1 V to 1 V
Frequency1 kHz

Interface

Interface 
USBUSB 3.0 SuperSpeed (5 Gbit/s);
(USB 2.0 HighSpeed compatible)
Network1 Gbps
WiFi802.11

Power Requirements

PowerFrom USB, external input or built-in battery
Consumption12 VDC 2 A max
External powerFrom power adapter
Internal batteryLi-ion
Capacity7000 mAh, 3.7 V
Weight160 g

Physical

Instrument
Height44 mm (1.7 inch)
Length187 mm (6.7 inch)
Width215 mm (5.2 inch)
Weight791 g (27.9 ounce)
USB cord length1.5 m (59 inch)

I/O connectors

Channel 1, 2, 3, 4Isolated BNC, female
LANRJ45 socket
USBUSB 3.0 type B Super Speed socket
Extension connectorD-sub 9 pins female
Power3.5 mm power socket
CMI connectors2 x HDMI type C socket

System requirements

PC I/O connectionUSB 2.0, USB 3.0 or USB 3.1
RJ45
WiFi
Operating systemWindows 10 / 11, 64 bits
Linux (via own software using the libtiepie-hw SDK)

Environmental conditions

Operating 
Ambient temperature20°C to 25°C for rated accuracy (10°C to 40°C without specifications)
Relative humidity10 % to 90 %, non condensing
Charging 
Ambient temperature0°C to 35°C
Relative humidity10 % to 90 %, non condensing
Storage 
Ambient temperature0°C to 35°C
Relative humidity5 % to 95 %, non condensing

Certifications and Compliances

CE mark complianceYes
RoHSYes
EN 55011:2009/A1:2010Yes
EN 55022:2006/A1:2007Yes
EN 61000-6-1:2007Yes
EN 61000-6-3:2007Yes

Package contents

Carry caseCarry case BB453
InstrumentAutomotive Test Scope ATS605004DW-XMS
Measure leads4 x Measure lead TP-C1812B, Differential BNC -> 4 mm banana plug
Differential attenuator4 x Differential attenuator TP-DA10
Alligator clips, largeAlligator Clip TP-AC80I - Set of 8: Green, Blue, Yellow, Red, 4 Black, 8 large alligator clips
Alligator clips, mediumAlligator Clip TP-AC10I - Set of 8: Green, Blue, Yellow, Red, 4 Black, 8 medium alligator clips
Alligator clips, smallAlligator Clip TP-AC5 - Set of 8: Green, Blue, Yellow, Red, 4 Black, 8 small alligator clips
AccessoriesGround compensation Cable TP-GCC150
Handyscope / WiFiScope power supply
USB3 cable, 1.5 m long
network cable, 3 m long
Softwarefor Windows 10 / 11, via website
Driversfor Windows 10 / 11, via website
Manualsinstrument manual and software user's manuals
color printed and digital, via website

Customer service

TiePie engineering instruments are designed, manufactured and tested to provide high reliability. In the unlikely event you experience difficulties, the TiePie engineering instruments are fully warranted for two years.
This warranty includesAll parts and labor (excluding probes and/or measure leads and/or batteries)
Warranty on batteries is 6 months.
No charge for return shipping
Long-term 7 year support
Upgrade to the latest software at no charge
Optionally availableExtension to five year warranty, option W5

The Automotive Test Scope ATS605004DW-XMS is delivered with:

Carry case Carry case BB453
Instrument Automotive Test Scope ATS605004DW-XMS
Measure leads 4 x Measure lead TP-C1812B, Differential BNC -> 4 mm banana plug
Differential attenuator 4 x Differential attenuator TP-DA10
Alligator clips, large Alligator Clip TP-AC80I - Set of 8: Green, Blue, Yellow, Red, 4 Black, 8 large alligator clips
Alligator clips, medium Alligator Clip TP-AC10I - Set of 8: Green, Blue, Yellow, Red, 4 Black, 8 medium alligator clips
Alligator clips, small Alligator Clip TP-AC5 - Set of 8: Green, Blue, Yellow, Red, 4 Black, 8 small alligator clips
Accessories Ground compensation Cable TP-GCC150
Handyscope / WiFiScope power supply
USB3 cable, 1.5 m long
network cable, 3 m long
Software for Windows 10 / 11, via website
Drivers for Windows 10 / 11, via website
Manuals instrument manual and software user's manuals
color printed and digital, via website
Complete set

Several downloads for the Automotive Test Scope ATS605004DW-XMS are listed below, including Multi Channel oscilloscope software, drivers and manuals.

Driver & Software

DescriptionVersionRemarksSize
WinUSB driver10.0.2Windows 10 / 11, 64 bit1.73 MB download
Multi Channel software1.47.0Windows 10 / 11, 64 bit, including PDF manual103.76 MB download

Firmware

DescriptionVersionRemarksSize
WiFiScope network module firmware2024-02-20287.31 MB download

Manuals & Documents

DescriptionVersionRemarksSize
Multi Channel software manual 1.11English3.13 MB download
Automotive Test Scope ATS605004DW-XMS Instrument manual2.49English1.41 MB download

Software Development Kit (SDK)

Interfacing the Automotive Test Scope ATS605004DW-XMS with third party software and developing own software requires the libtiepie-hw Software Development Kit. Detailed information on the libtiepie-hw SDK, downloads for Windows and Linux platforms and bindings and programming examples for various programming environments can be found in the libtiepie-hw pages.