High performance lab scope for the automotive technician
Price: € 2,246.00
Key specifications
- Differential inputs
- 12, 14, 16 bit resolution, 0.3 % DC accuracy
- Up to 50 MSa/s sampling, 50 MHz bandwidth
- 128 kpoints memory per channel
Full specifications Manual Request info
Order code: ATS5004DW
EAN: 7423624548537
Price: 2,246.00
WiFi connected
Using a computer based oscilloscope was never easier than with the Automotive Test Scope ATS5004DW: simply switch it on and start the software on the computer:
- no power cables required as it is battery powered and can operate hours on a fully charged battery
- no interface cables required as it uses WiFi to connect to the computer
This allows you to measure fully floating, fully isolated from your computer. The Automotive Test Scope ATS5004DW can be placed near any test subject that may be hard to reach, or on moving objects, where wired connections are not possible.
Because the Automotive Test Scope ATS5004DW is not connected to the computer, there is no risk of damaging the computer.
LAN connected
When measuring in remote locations where a wired network is available, the Automotive Test Scope ATS5004DW can also be used through its LAN port. Measurements can then be performed from any location via the network, without having the computer to be close to the test subject.
Using its 1 Gbit LAN connection, the Automotive Test Scope ATS5004DW can achieve higher streaming performance than via WiFi.
USB connected
When wireless measuring or LAN connected measuring is not required or not possible, the Automotive Test Scope ATS5004DW can also be connected via its USB port. This gives the benefit of even higher streaming performance.
The Automotive Test Scope ATS5004DW is a 4 channel automotive WiFi oscilloscope with differential inputs. Besides the normal features of a professional USB oscilloscope, the Automotive Test Scope ATS5004D has some specific features like SureConnect connection test and resistance measurement that make it an ideal instrument for automotive measurements.
Rugged industrial design
The Automotive Test Scope ATS5004DW features a rugged design. Its enclosure is fitted with rubber protectors at the front and the rear. These protect the Automotive Test Scope ATS5004DW against damage by mechanical shocks. The rubber helps absorbing shocks and protects the connectors at the front and the rear of the Automotive Test Scope ATS5004DW, these fall within the protected zone.
Additionally, the rubber prevents your Automotive Test Scope ATS5004DW from sliding. The rubber protectors have special notches that simplify stacking instruments. Holes are included that allow to connect a strap to hang the instrument near the test subject.
Differential inputs
The Automotive Test Scope ATS5004DW features four isolated differential input channels. This makes it the ideal instrument to perform measurements in high voltage circuits, amplifiers, switch mode power supplies, power inverters etc. No more risk of creating short circuits through your oscilloscope!
Connection test
The SureConnect connection test feature of the Automotive Test Scope ATS5004DW tells you immediately whether your test probe or clip actually makes electrical contact or not. No more doubt whether your probe doesn't make contact or there really is no signal.
This is useful when surfaces are oxidized and your probe cannot get a good electrical contact. Simply activate the SureConnect and you know whether there is contact or not. Also when back probing connectors in confined places, SureConnect immediately shows whether the probes make contact or not.
Resistance measurement
Many automotive sensors are based on variable resistors. Use your Automotive Test Scope ATS5004DW in the resistance setting to test them, no more need to take a separate ohm meter. Resistance values can be displayed as a number, but it is also possible to display the resistance variation in time, in a graph.
Fully supported by ATIS
All features of the Automotive Test Scope ATS5004DW are fully supported by ATIS, the Automotive Test and Information System. Select a specific diagnostic measurement in ATIS, click the measure button and the Automotive Test Scope ATS5004DW will be completely setup for that specific measurement and ready to perform it.
Automotive Test Scope ATS5004DW specifications
The tables below show detailed specifications of the Automotive Test Scope ATS5004DW. Jump to specifications regarding
Acquisition system | |||||
|---|---|---|---|---|---|
| Number of input channels | 4 analog | ||||
| Ch1, Ch2, Ch3, Ch4 | Isolated female BNC | ||||
| Type | Differential | ||||
| Resolution | User selectable in software | ||||
| Native | 12 bit | ||||
| Enhanced | 14, 16 bit | ||||
| Accuracy | 0.3 % of full scale ± 1 LSB | ||||
| Ranges (Full scale) | ±200 mV ±400 mV ±800 mV | ±2 V ±4 V ±8 V | ±20 V ±40 V ±80 V | ||
| Coupling | AC/DC | ||||
| Impedance | 2 MΩ / 40 pF | ||||
| Noise (in 200 mV range) | 135 µVrms | ||||
| Maximum input voltage (in all ranges) | ±200 V (DC + AC peak < 10 kHz) with 1:10 attenuator ±300 V (DC + AC peak < 10 kHz) | ||||
| Maximum Common Mode voltage | 200 mV to 800 mV ranges : 2 V 2 V to 8 V ranges : 20 V 20 V to 80 V ranges : 200 V | ||||
| Common Mode Rejection Ratio | -48 dB | ||||
| Bandwidth (-3dB) | DC to 50 MHz maximum | ||||
| AC coupling cut off frequency (-3dB) | 1 Hz | ||||
| Channel Isolation | 500 V | ||||
| Channel Separation | -80 dB | ||||
| SureConnect | |||||
| Maximum voltage on connection | 200 V (DC + AC peak < 10 kHz) | ||||
| Resistance measurement | |||||
| Ranges (Full scale) | 100 Ω 200 Ω 500 Ω | 1 kΩ 2 kΩ 5 kΩ | 10 kΩ 20 kΩ 50 kΩ | 100 kΩ 200 kΩ 500 kΩ | 1 MΩ 2 MΩ |
| Accuracy | 3% | ||||
| Response time (to 95%) | < 5 ms | ||||
| Maximum sampling (on all channels simultaneously) | 12 bit | 14 bit | 16 bit | ||
| Scope mode (block) | 50 MSa/s | 3.125 MSa/s | 195.3 kSa/s | ||
| Streaming mode | 500 kSa/s | 480.8 kSa/s | 195.3 kSa/s | ||
| Sampling clock source | |||||
| Internal | Quartz | ||||
| Accuracy | ±0.01 % | ||||
| Stability | ±100 ppm over -40 °C to +85 °C | ||||
| Time base aging | ±5 ppm/year | ||||
| External | On extension connector | ||||
| Voltage | 3.3 V TTL, 5 V TTL tolerant | ||||
| Frequency range | 95 MHz to 105 MHz | ||||
| Memory | 128 KSamples per channel | ||||
| Trigger | Only available in scope/block mode, not in streaming mode | ||||
| System | Digital, 2 levels | ||||
| Source | CH1, CH2, CH3, CH4, OR, digital external | ||||
| Trigger modes | Rising edge, Falling edge Inside window, Outside window | ||||
| Level adjustment | 0 to 100 % of full scale | ||||
| Hysteresis adjustment | 0 to 100 % of full scale | ||||
| Resolution | 0.025 % (12 bits) | ||||
| Pre trigger | 0 to 131071 samples, 1 sample resolution | ||||
| Post trigger | 0 to 131071 samples, 1 sample resolution | ||||
| Trigger hold-off | 0 to 1048576 Samples, 1 sample resolution | ||||
| Digital external trigger | |||||
| Input | Extension connector | ||||
| Range | 0 to 3.3 V (5 V max) | ||||
| Coupling | DC | ||||
Interface | |||||
| Interface | |||||
| USB | 2.0 High Speed (480 Mbit/s) | ||||
| Network | 1 Gbps | ||||
| WiFi | 802.11 | ||||
Power Requirements | |||||
| Power | From USB, external input or built-in battery | ||||
| Consumption | 12 VDC 2 A max | ||||
| External power | From power adapter | ||||
| Internal battery | Li-ion | ||||
| Capacity | 7000 mAh, 3.7 V | ||||
| Weight | 160 g | ||||
Physical | |||||
| Instrument | |||||
| Height | 44 mm (1.7 inch) | ||||
| Length | 187 mm (6.7 inch) | ||||
| Width | 215 mm (5.2 inch) | ||||
| Weight | 791 g (27.9 ounce) | ||||
I/O connectors | |||||
| Channel 1...4 | Isolated BNC, female | ||||
| LAN | RJ45 socket | ||||
| USB | USB 3.0 type B Super Speed socket | ||||
| Extension connector | D-sub 25 pins female | ||||
| Power | 3.5 mm power socket | ||||
System Requirements | |||||
| PC I/O connection | USB 2.0, USB 3.0 or USB 3.1 RJ45 WiFi | ||||
| Operating System | Windows 10 / 11, 64 bits Linux (via own software using the libtiepie-hw SDK) | ||||
Operating Environment | |||||
| Operating | |||||
| Ambient temperature | 20°C to 25°C for rated accuracy (10°C to 40°C without specifications) | ||||
| Relative humidity | 10 % to 90 %, non condensing | ||||
| Charging | |||||
| Ambient temperature | 0°C to 35°C | ||||
| Relative humidity | 10 % to 90 %, non condensing | ||||
| Storage | |||||
| Ambient temperature | 0°C to 35°C | ||||
| Relative humidity | 5 % to 95 %, non condensing | ||||
Certifications and Compliances | |||||
| CE mark compliance | Yes | ||||
| RoHS | Yes | ||||
| EN 55011:2009/A1:2010 | Yes | ||||
| EN 55022:2006/A1:2007 | Yes | ||||
| EN 61000-6-1:2007 | Yes | ||||
| EN 61000-6-3:2007 | Yes | ||||
Package | |||||
| Convenient carrying case | Carry case BB453 | ||||
| Instrument | Automotive Test Scope ATS5004DW | ||||
| Measure leads | 4 x Measure lead TP-C1812B, BNC -> 4 mm banana plug | ||||
| Differential attenuator | 4 x Differential attenuator TP-DA10 | ||||
| Accessories | Ground compensation Cable TP-GCC150 Handyscope / WiFiScope power supply USB3 cable, 1.5 m long network cable, 3 m long | ||||
| Software | Windows 10 / 11, via website | ||||
| Drivers | Windows 10 / 11, via website | ||||
| Manual | instrument manual and software user's manuals color printed and digital, via website | ||||
| Total package weight | Approx. 3 kg | ||||
Customer service | |||||
| TiePie engineering instruments are designed, manufactured and tested to provide high reliability. In the unlikely event you experience difficulties, the TiePie engineering instruments are fully warranted for two years. | |||||
| This warranty includes | All parts and labor (excluding probes and/or measure leads and/or batteries) Warranty on batteries is 6 months. No charge for return shipping Long-term 7 year support Upgrade to the latest software at no charge | ||||
The Automotive Test Scope ATS5004DW is delivered with:
| Carry case | Carry case BB453 |
|---|---|
| Instrument | Automotive Test Scope ATS5004DW |
| Measure lead | 4x Measure lead TP-C1812B, Differential BNC -> 4 mm banana plug |
| Attenuator | 4x Differential attenuator TP-DA10 |
| Accessories | Ground compensation Cable TP-GCC150 Handyscope / WiFiScope power supply USB3 cable, 1.5 m long network cable, 3 m long |
| Software | for Windows 10 / 11, via website |
| Drivers | for Windows 10 / 11, via website |
| Manuals | instrument manual and software user's manuals color printed and digital, via website |
Several downloads for the Automotive Test Scope ATS5004DW are listed below, including Multi Channel oscilloscope software, drivers and manuals.
Driver & Software
| Description | Version | Remarks | Size | |
|---|---|---|---|---|
| WinUSB driver | 10.0.2 | Windows 10 / 11, 64 bit | 1.73 MB | download |
| Multi Channel software | 1.47.0 | Windows 10 / 11, 64 bit, including PDF manual | 103.76 MB | download |
Firmware
| Description | Version | Remarks | Size | |
|---|---|---|---|---|
| WiFiScope network module firmware | 2024-02-20 | 287.31 MB | download |
Manuals & Documents
| Description | Version | Remarks | Size | |
|---|---|---|---|---|
| Multi Channel software manual | 1.11 | English | 3.13 MB | download |
| Automotive Test Scope ATS5004DW instrument manual | 2.49 | English | 1.24 MB | download |
Software Development Kit (SDK)
Interfacing the Automotive Test Scope ATS5004DW with third party software and developing own software requires the libtiepie-hw Software Development Kit. Detailed information on the libtiepie-hw SDK, downloads for Windows and Linux platforms and bindings and programming examples for various programming environments can be found in the libtiepie-hw pages.
